Production Status and Hot Spots of Microwave Signals in Microwave Optoelectronics
May 29, 2018
Microwave optoelectronics, as its name suggests, is an interdisciplinary discipline of microwave and optoelectronics. Both microwaves and light waves are electromagnetic waves, and their frequencies are many orders of magnitude different. The components and technologies developed in their respective fields are very different. Combining and learning from each other's strengths can yield new applications and features that are difficult to achieve [1,2,3].
Optical communication is a best example of a combination of microwave and optoelectronics. Early telephone telegraphy wireless communication, signal generation, propagation and reception are all microwave devices used. Low-frequency electromagnetic waves are used at first, because the frequency range is small, and the transmission channel capacity is small. The solution is to increase the frequency of the transmitted signal. The higher the frequency, the more spectral resources. However, high-frequency signals have large propagation losses in the air and are easily obstructed by obstacles. If you use wired transmission, the loss of the cable is large, and long-distance transmission is a problem. The emergence of fiber optic communications has solved these problems. Optical fiber transmission loss is very low, it is an excellent carrier for transmitting signals over long distances. The frequency range of light waves far exceeds microwaves, and many different channels can be transmitted at the same time. Because of these advantages of optical transmission, optical fiber communication has become the backbone of today's information dissemination.
Optical communication has a long history, research and application are very extensive and mature, I will not say more here. Here I mainly want to introduce the research content of other emerging microwave optoelectronics other than optical communication in recent years. Microwave optoelectronics is mainly based on methods and techniques in the field of optoelectronics to improve and realize the performance and applications that are difficult to achieve with traditional microwave electronic components. From the application perspective, it mainly includes the following three aspects.
First, the use of optoelectronics to produce high-performance, low-noise microwave signals, from the X-band to the THz band.
Second, the processing of microwave signals. Including delay, filtering, frequency conversion, receiving and so on.
Third, analog signal transmission.
This article only introduces the first part of the article, the generation of microwave signals. The traditional microwave millimeter wave is mainly produced by iii_V microelectronic components [4]. Its limitations are the following: First, to high frequencies such as 100 GHz or more, traditional microelectronic components can produce less and less power, and to higher frequency THz signals, they are powerless. Second, in order to reduce the phase noise and improve the frequency stability, the original device needs to be placed in a cryogenic environment. Third, it is difficult to achieve a wide range of FM frequency conversion. To solve these problems, optoelectronics technology can just show itself. Here are some of the main methods.
1. By using the difference frequency of two different frequency laser signals, a high-frequency photodetector converts to generate a microwave signal [5, 6], as shown in FIG. 1 .
Figure 1. Schematic diagram of two laser differential frequency microwave generation.
The advantage of this method is that it has a simple structure and can generate signals of extremely high frequency, millimeter wave and even THz frequency. Moreover, by adjusting the frequency of the laser, a wide range of rapid frequency conversion and frequency sweeping can be performed. The disadvantage is that the line width or phase noise of the difference frequency signal produced by two incoherent laser signals is relatively large, and the frequency stability is not high, especially if a small-sized but wide (~MHz) semiconductor laser is used. . If the system's weight and volume requirements are not high, a low-noise (~kHz) solid-state laser, fiber laser [7,8], external cavity semiconductor laser [9], etc. can be used. In addition, two different modes of laser signals generated in the same laser cavity can also be used to generate the difference frequency, so that the resulting microwave frequency stability can be greatly improved [10-12].
2. In order to solve the problem that the two lasers in the previous method are incoherent and the phase noise of the generated signal is too large, an injection locking method or a negative feedback phase locked circuit can be used to obtain the coherence between the two lasers [ 13]. Figure 2 shows a typical application of injection-locked frequency multi-frequency microwave generation (Figure 2). By directly injecting a high-frequency current signal to the semiconductor laser, or using a LiNbO3 phase modulator, a plurality of optical signals having different frequencies at equal intervals can be generated, or an optical frequency comb. Of course, the commonly used method for obtaining a wide-spectrum optical frequency comb is to use a mode-locked laser [14]. Any two comb signals of the generated optical frequency comb are selected by filtering and injected into the lasers 1 and 2 respectively to achieve frequency locked locking. Because the phase between the different comb signals of the optical comb is relatively stable, a stable relative phase between the two lasers is obtained, and the frequency of the comb repeat can be obtained by the method of difference frequency as described above. Multiple frequency microwave signal.
Figure 2. Schematic diagram of injection-locked frequency generation of microwave frequency-doubled signals.
Another way to reduce the relative phase noise of the two lasers is to use a negative feedback optical phase-locked loop, as shown in Figure 3.
Figure 3. Optical PLL schematic.
The principle of optical phase locked loop is similar to the phase locked loop in the electronic field [15,16,17]. The phase difference of the two lasers is converted into an electrical signal by a photodetector (corresponding to a phase detector), and the difference between the two lasers is obtained by difference frequency with the reference microwave signal source, and the feedback is returned to the two lasers after amplification and filtering. A laser frequency control unit (injection current for semiconductor lasers). With such a negative feedback control loop, the relative frequency between the two laser signals is phase locked with the reference microwave signal. The combined optical signal can then be transmitted through an optical fiber to a photodetector elsewhere and converted to a microwave signal. The phase noise of the microwave signal thus generated is almost the same as the phase noise of the reference signal in the bandwidth of the phase-locked negative feedback loop. Phase noise outside the bandwidth is equal to the relative phase noise of the original two incoherent lasers.
In addition, the reference microwave signal source may also be another signal source that is processed by frequency conversion, digital frequency, or other frequency conversion, so that the microwave signal with lower frequency may be multi-frequency-converted or converted to high frequency. Radio frequency, THz signal and so on.
Compared with injection-locked frequency, which can only obtain frequency multiplication, phase-locked loops are more flexible, can generate almost any frequency, and of course, are more complex. For example, in FIG. 2 , phase modulated by an optoelectronic modulator, or an optical comb generated by a pulsed laser as a light source, an optical phase-locked loop is used to selectively lock two lasers to two of the optical comb-tooth signals. Generate high-frequency signals through the difference frequency, as shown in Figure 4. F1 and f2 are the reference signal frequencies of the two phase-locked loops respectively, and a microwave signal of N*frep+f1+f2 can be generated by the difference frequency between the two lasers.
Figure 4. Generates an arbitrary frequency diagram using optical combs and optical PLLs.
3. Using a mode-locked pulsed laser, the optical pulse signal is converted to a microwave signal by a photodetector [18-20].
The main advantage of this method is that a signal with very good frequency stability and extremely low phase noise can be obtained. By locking the frequency of the laser to a very stable atomic molecular transition spectrum, or an extremely stable optical cavity, and using self-multiplying frequency to eliminate system frequency shifts, etc., optical pulse signals with very stable repetition frequencies can be obtained. Ultra-low phase noise microwave signal [21-23]. As shown in Figure 5.
Figure 5. Comparison of relative phase noise of different signal sources. Excerpt from reference [21]
However, because the repetition frequency of the pulse is inversely proportional to the cavity length of the laser, while the conventional mode-locked laser has a large volume, it is difficult to directly obtain high-frequency microwave signals. In addition the traditional pulsed laser volume, weight and energy consumption, as well as the harsh requirements of the environment have limited their use primarily in the laboratory. In order to overcome these difficulties, the most advanced research in the United States and Germany used nonlinear effects to generate frequency-stable optical combs in a small, high-quality mode cavity to generate high-frequency, low-noise microwave signals.[24-29] ].







