Overview of LED backlight application technology

Nov 10, 2021

LEDs used for LCD backlighting are divided into edge lighting, which is mainly used for medium and small equipment, and direct lighting, which is used for large-area equipment, such as LCD-TV.

1. Edge Lighting

The basic structure of Edge lighting is shown in Figure 1.

figure 1

The light emitted by the LED is emitted upward through the optical action of the light guide plate (Light Guide Plate) to form a surface light source, and then through the diffuser plate (Diffuser Plate) and the brightness enhancement film (BEF) to form a light spot with uniform brightness and color distribution on the LCD panel.

The diffuser can increase the uniformity of the light distribution. The brightness enhancement film can concentrate the light into a certain angle on the front side and increase the front brightness. However, excessive use of the diffuser and the brightness enhancement film will increase the light loss and reduce the overall light efficiency. The film has been monopolized by patents and the cost is relatively high. Therefore, increasing the uniformity of the direct light output from the light guide plate through optical design is the focus of the side-down backlight design.

The optical design of the front end is mainly divided into: (1) the design of the LED light coupled into the light guide plate (2) the optical structure design of the light guide plate

1.1 Light coupling between LED and light guide plate

(1) Direct coupling

The schematic diagram of the structure is shown in Figure 2. Generally speaking, direct coupling can improve the efficiency of the LED light entering the light guide plate. The structure is simple. At the same time, the RGB three-color light is not fully mixed before entering the light guide plate, which may lead to the uniform color of the final light. The performance is not good, especially for the structure where the light path in the light guide plate is short.

figure 2

(2) Indirect coupling

The structure diagram is shown in Figure 3. There are two advantages of indirect coupling: (1) Scatter and atomize the light before entering the light guide plate to improve uniformity (2) Full color mixing

image 3

LEDs used for LCD backlighting are divided into edge lighting, which is mainly used for medium and small equipment, and direct lighting, which is used for large-area equipment, such as LCD-TV.

1. Edge Lighting

The basic structure of Edge lighting is shown in Figure 1.

figure 1

The light emitted by the LED is emitted upward through the optical action of the light guide plate (Light Guide Plate) to form a surface light source, and then through the diffuser plate (Diffuser Plate) and the brightness enhancement film (BEF) to form a light spot with uniform brightness and color distribution on the LCD panel.

The diffuser can increase the uniformity of the light distribution. The brightness enhancement film can concentrate the light into a certain angle on the front side and increase the front brightness. However, excessive use of the diffuser and the brightness enhancement film will increase the light loss and reduce the overall light efficiency. The film has been monopolized by patents and the cost is relatively high. Therefore, increasing the uniformity of the direct light output from the light guide plate through optical design is the focus of the side-down backlight design.

The optical design of the front end is mainly divided into: (1) the design of the LED light coupled into the light guide plate (2) the optical structure design of the light guide plate

1.1 Light coupling between LED and light guide plate

(1) Direct coupling

The schematic diagram of the structure is shown in Figure 2. Generally speaking, direct coupling can improve the efficiency of the LED light entering the light guide plate. The structure is simple. At the same time, the RGB three-color light is not fully mixed before entering the light guide plate, which may lead to the uniform color of the final light. The performance is not good, especially for the structure where the light path in the light guide plate is short.

figure 2

(2) Indirect coupling

The structure diagram is shown in Figure 3. There are two advantages of indirect coupling: (1) Scatter and atomize the light before entering the light guide plate to improve uniformity (2) Full color mixing

image 3

A specific indirect coupling structure of Lumileds is shown in Figure 4:

Figure 4

In the figure, ③ is a mixed-color waveguide, ②④ is a coupling lens, and its structure is a conical surface to reduce the light loss during the two coupling processes. The physical map is shown in Figure 5.

Figure 5

(3) Coupling structure using free-form surface mirror

In order to fully improve the uniformity of LED light before entering the light guide plate, some designs use free-form surface mirrors, as shown in Figure 6.

Image 6

The red in the picture is the LED light source. The conventional side-down light source is arranged as an LED array. After the free-form surface reflector is applied, the LED light source can only be arranged on both sides or even one side of the LED Uniform Light guide. Figure 7 shows a specific form of LED uniform lightguide

Figure 7

The free-form surface coupling design can improve the uniformity of the light entering the light guide plate and reduce the volume of the system at the same time.

1.2 Light guide plate structure design

1.2.1 The bottom structure of the light guide plate

The light guide plate reflects the incident light from the side to the front to emit light through the bottom structure. From the CCFL light source to the LED light source, the light guide plate has a variety of optical structures, for example:

(1) Dot printing structure. The scattering dots printed on the bottom of the light guide plate change the direction of the incident light on the side. The dot distribution is based on a certain distribution theory. Generally speaking, the farther away from the light source, the denser the dot distribution.

(2) Micro prism structure

(3) V-groove structure. As shown in Figure 8, applying boundary light conditions, each V-shaped groove corresponds to the area of the target surface on a one-to-one basis.

Figure 8

(4) Gradient refractive index polymer materials. The use of graded refractive index materials to reflect light in the light guide can achieve a one-time molding of the light guide plate.

1.2.2 Shape design of light guide plate

In addition to the bottom structure, the shape of the light guide plate can also have a variety of structures, such as a wedge structure as shown in FIG. 9 and even an aspherical surface structure as shown in FIG. 10.

Picture 9

Picture 10

The side-down backlight design should comprehensively use the above various structures to improve light efficiency, illumination uniformity and color uniformity.

2 Direct Lighting

Compared with the side-down type, the direct type has a simple structure and does not have a light guide plate. It can obtain a good illuminance uniformity on a large-size backlight. At the same time, because the light mixing distance is short, the color uniformity is not easy to control; and the thickness of the direct type is average It is larger than the side-down type, the overall light efficiency is not as good as the side-down type, and the total number of LEDs consumed is a little more. In the small and medium-sized equipment, the advantage of the direct type is not obvious.

The basic structure of the direct backlight is shown in Figure 11

Picture 11

(1) If the LED is regarded as a point light source, it can be concluded from Figure 12 that the condition of the uniform illuminance of the target surface is the luminous intensity of the LED

Picture 12

That is, look for an LED with the above-mentioned light distribution. A relatively simple idea is to use LEDs with batwing light distribution similar to the above-mentioned light distribution, and then adjust the parameters of h and the reflecting cavity wall to simulate the illuminance and color distribution of the target surface. At present, people in China have done the above work, and the theoretical uniformity has not yet reached 85%.

(2) Lumileds' backlight products

This is the most common LED direct-lit backlight module on the market. As shown in Figure 13, two RGB LED arrays are placed at the bottom of the cavity, and optical films such as a diffuser and BEF are placed on the top.

Figure 13

Each LED array adopts the G-B-R-G arrangement, as shown in Figure 14, there are a total of 24 unit arrays in two columns.

Figure 14

Single LED adopts Lumileds' newly designed side light emitting structure for direct type LED backlight, which has a higher proportion of light emitted in the horizontal direction than the batwing light distribution. The schematic diagram of a single LED and the spatial distribution of light intensity are shown in Figure 15 and Figure 16, respectively.

Figure 15

Figure 16

For this structure, National Taiwan University has done a reverse simulation. When the diffuser and the brightness enhancement film are not added, the illuminance and color uniformity have a good performance, but there is still a phenomenon of lamp shadow.

(3) Optimized Lumileds backlight structure

National Taiwan University has made optimizations on the basis of Lumileds backlight products, such as changing two rows of LEDs to three rows, and creating a V-groove structure at the bottom of the reflective cavity to reduce lamp shadows. The basic idea is roughly the same as that of Lumileds products.

(4) Micro lens structure

Place a micro lens array in front of the LED light source to change the light distribution. As shown in Figure 17, the dotted line is the light distribution curve before the micro lens array is placed, and the solid line is after the micro lens array is placed. Compared with changing the light distribution of a single LED, the overall placement of the microlens array weakens the control of light, and it is possible to increase the thickness of the backlight. GLT has applied for a patent for the micro lens array technology.

Figure 17

(5) Use ASP backlight

Our own ASP LED light source can be used, and the illumination uniformity and overall light efficiency are expected to reach a very good level. The key issues are color uniformity and overall thickness.

The current plan is to reversely simulate the existing direct-lit LED backlights and find their problems, and then use ASP light sources to design a backlight structure. If the color uniformity cannot meet the requirements, consider introducing a hybrid for direct-lit LED backlights. Optical waveguide.


You Might Also Like